nolanlabs

Blog · The cut

J-cuts and L-cuts: how many frames, and when not to

· 5 min read

Seen from directly above at dusk, two long red planks lie on a pale salt flat, overlapping at an offset.

Short answer

A J-cut starts the next shot’s sound before its picture; an L-cut carries the last shot’s sound over the next picture. As a starting range, in our judgment, use 6–14 frames at 24 fps to soften a dialogue cut and 1–3 seconds to lead into a new scene. Stay straight on punchlines, sync hits and shots where a mouth is still moving.

On this page
  1. How many frames should the split be?
  2. Where should the picture cut land?
  3. How do you do it on a timeline with linked sound?
  4. When shouldn’t you split the cut?
  5. How does this work in nolanlabs?

Those ranges aren’t a standard or a measurement. What should set the final number is where the picture cut wants to land.

How many frames should the split be?

Start from the situation. Every range below is our judgment at 24 fps, so treat it as a place to begin and a way to notice when you’re far off. Multiply by 1.25 for 30 fps.

Situation Cut Frames at 24 fps Duration What decides it
A sound makes someone look: a horn, a door, their name J 4–8 0.17–0.33 s How fast a person would turn
Softening a plain cut between two speakers J 6–14 0.25–0.58 s The breath or first word before the face
Going to the listener before the line ends L 8–24 0.33–1 s When the reaction starts, not when the line ends
Interview into or out of B-roll J or L 12–36 0.5–1.5 s A break between phrases
Scene change, old sound trailing out L 12–48 0.5–2 s The last line or the fade of the room
Scene change, new sound arriving first J 24–72 1–3 s How long you want the viewer asking where this is
Fast social cut or trailer, with shots under about 2 s J or L 2–4 0.08–0.17 s Often none at all

One published reference point: a lesson in Blackmagic’s Editor’s Guide to DaVinci Resolve 20 rolls the picture cut from an opening landscape into an interview by about 15 frames, stopping when the speaker’s hand has come down. It chose that length from what the frame showed, not from a rule.

Where should the picture cut land?

Find the frame first and let the count follow. A split has two cuts, and the sound cut usually stays where the words want it. The picture cut is the one you’re placing, and there are three good places to look:

  • Where a viewer would look anyway. Blackmagic’s guide explains the J-cut with a car horn: you hear it, and a moment later you look for it. Roll to the moment your attention would move.
  • Where the reaction begins. For an L-cut, find the first frame the listener’s face changes, then come back a few frames. The guide describes the L-cut as a way to show a reaction before the response.
  • Just before a blink. Walter Murch told Steve Hullfish that the moment to cut is generally a frame or two before an actor in character blinks, and that you should override this when your sense of the shot says otherwise.

Then look at the number. If you’ve landed at 40 frames on a plain dialogue cut, that’s not wrong, but you’ve made something the viewer will notice, so make sure you meant to.

How do you do it on a timeline with linked sound?

Roll the picture cut alone, and leave the link in place. Rolling picture alone needs handles, so check them first. A J-cut runs the outgoing picture past its sound, so that clip needs frames beyond its tail. An L-cut starts the incoming picture early, so that clip needs frames before its head. A roll keeps the total length, so nothing downstream moves.

As of November 2026, the vendors document it like this:

Editor Get at the picture alone Make the split
Premiere (help updated August 2025) Click the Linked Selection icon in the Timeline panel to turn it off Select the picture or sound on its own and adjust the overlap
Resolve (Editor’s Guide for version 20) Shift-Command-L on a Mac, Shift-Ctrl-L on Windows, toggles Linked Selection Click the video edit point and drag, or place the playhead and press E (Trim > Extend Edit) to roll the selected edit to it. Toggle the link back on afterward
Final Cut Pro (12.4) Control-S (Clip > Expand Audio). On the edit, Backslash selects the video edit point, Shift-Backslash both sides of the audio edit point Comma and Period nudge a frame, Shift-Comma and Shift-Period nudge 10

Final Cut has one extra step worth knowing. Apple notes that dragging the video’s start point right leaves the clip’s audio overlapping the clip before it, so you then pull the earlier clip’s audio back or balance the two with fades or keyframes.

Whichever editor you’re in, listen to the frames you’ve just exposed. Handles are whatever the recorder caught: another actor’s line, a chair, someone saying “cut.”

When shouldn’t you split the cut?

These are our judgment too.

  • Punchlines and sync hits. A joke, a door slam or a punch works because sight and sound arrive together. A split takes the edge off, so keep it straight, or a frame or two at most.
  • When a mouth is still moving. This is the most common failure. Run the outgoing picture past its sound while that person is still talking, and you’ve got lips moving under someone else’s voice. Check every frame of the overlap.
  • When there’s no reaction to cut to. An L-cut to a listener who’s only waiting for their next line tells the viewer nothing. A straight cut is more honest.
  • When the rooms don’t match. Sound carried from one room over another shows up the difference in tone. Add a fade or fill, or don’t split there.
  • When the words point at the picture. In a tutorial, a voice saying “click here” over a shot of something else sends the viewer to the wrong place.
  • When every cut is already split. Splits work against straight cuts. If nothing in the scene ever lands together, the viewer loses the anchor that made the overlaps feel smooth.

Cutting to music adds another constraint, because the picture cut may belong to a beat and not to the line.

How does this work in nolanlabs?

In nolanlabs, our editor, dragging a cut moves linked picture and sound together. To split them in Pro, select the pair and press the link button above the timeline, or Ctrl+Alt+L, then trim each on its own. Or ask for “a 10-frame J-cut into the reaction,” and your agent can do the same with clip.unlink and clip.roll. The limit is that the sync check only watches linked clips, so link them again when the cut is right.

Blog

Keep reading.

Every piece

Written by the people who make nolanlabs, a video editor that edits with you.

Download for Mac Download for Windows Download

Free to start, on Mac and Windows.